You can receive full credit for NCCER’s Project Management and Project Supervision training as well your initial training in this career field. In addition, you are eligible to receive credit for the 4 modules* in the following craft* areas: Carpentry, Masonry, Painting and Sheet Metal. In the chart below, an X next to a module indicates you are eligible to receive credit for that module.
If an X does not appear next to a module then additional training is required for the craft level* completion. Each module builds upon one another to accomplish a level completion and this information is tracked in NCCER’s Registry System. An industry- recognized credential* is awarded with level completions and each craft usually has three to four levels.
*Refer to NCCER’s definitions located on the right side of the screen to fully understand these terms.
Sheet Metal
This four-level curriculum is designed to prepare the trainee for a large range of possibilities, covering topics such as Installation of Ductwork, Bend Allowances, and Advanced Architectural Sheet Metal.
| Craft | Level | Module | Title | Credit |
|---|---|---|---|---|
| Sheet Metal | 1 | 04101-08 | Introduction to Sheet Metal Trade | |
| Sheet Metal | 1 | 04102-08 | Tools of the Trade | |
| Sheet Metal | 1 | 04103-08 | Introduction to Sheet Metal Layout and Processes | |
| Sheet Metal | 1 | 04104-08 | Trade Math One | |
| Sheet Metal | 1 | 04105-08 | Fabrication One- Parallel Line Development | |
| Sheet Metal | 1 | 04106-08 | Installation of Ductwork | |
| Sheet Metal | 1 | 04107-08 | Installation of Air Distribution Accessories | |
| Sheet Metal | 1 | 04108-08 | Insulation | |
| Sheet Metal | 1 | 04109-08 | Architectural Sheet Metal | |
| Sheet Metal | 2 | 04201-08 | Trade Math Two | |
| Sheet Metal | 2 | 04202-08 | Plans and Specifications | |
| Sheet Metal | 2 | 04203-08 | Fabrication Two- Radial Line Development | |
| Sheet Metal | 2 | 04204-08 | Sheet Metal Duct Fabrication Standards | |
| Sheet Metal | 2 | 04205-08 | Air Properties and Distribution | |
| Sheet Metal | 2 | 04206-08 | Bend Allowances | |
| Sheet Metal | 2 | 04207-08 | Soldering | |
| Sheet Metal | 2 | 04208-08 | Basic Piping Practices | |
| Sheet Metal | 2 | 04209-08 | Fiberglass Duct | |
| Sheet Metal | 3 | 04301-09 | Trade Math Three- Field Measuring and Fitting | |
| Sheet Metal | 3 | 04302-09 | Air Systems | |
| Sheet Metal | 3 | 04303-09 | Principles of Airflow | |
| Sheet Metal | 3 | 04304-09 | Louvers, Dampers and Access Doors | |
| Sheet Metal | 3 | 04305-09 | Comprehensive Plan and Specification Reading | |
| Sheet Metal | 3 | 04306-09 | Fabrication Three- Triangulation | |
| Sheet Metal | 3 | 04307-09 | Advanced Architectural Sheet Metal | |
| Sheet Metal | 4 | 04401-09 | Shop Production and Organization | x |
| Sheet Metal | 4 | 04402-09 | Air Testing and Balancing | |
| Sheet Metal | 4 | 04403-09 | Introduction to Welding, Brazing and Cutting | |
| Sheet Metal | 4 | 04404-09 | Fume and Exhaust System Design | |
| Sheet Metal | 4 | 04405-09 | Fabrication Four- Comprehensive Review | |
| Sheet Metal | 4 | 04406-09 | Introductory Supervisory Skills | |
Carpentry
This four-level curriculum covers content such as Building Materials, Cabinet Fabrication, and Advanced Wall Systems.
| Craft | Level | Module | Title | Credit |
|---|---|---|---|---|
| Carpentry | 1 | 27101-13 | Orientation to the Trade | |
| Carpentry | 1 | 27102-13 | Building Materials, Fasteners, and Adhesives | x |
| Carpentry | 1 | 27103-13 | Hand and Power Tools | |
| Carpentry | 1 | 27104-13 | Introduction to Construction Drawings, | |
| Carpentry | 1 | 27105-13 | Floor Systems | |
| Carpentry | 1 | 27111-13 | Wall Systems | |
| Carpentry | 1 | 27112-13 | Ceiling Joist and Roof Framing | |
| Carpentry | 1 | 27110-13 | Basic Stair Layout | x |
| Carpentry | 1 | 27109-13 | Introduction to Building Envelope Systems | |
| Carpentry | 2 | 27201-13 | Commercial Drawings | |
| Carpentry | 2 | 27202-13 | Roofing Applications | |
| Carpentry | 2 | 27203-13 | Thermal and Moisture Protection | |
| Carpentry | 2 | 27204-13 | Exterior Finishing | |
| Carpentry | 2 | 27205-13 | Cold-Formed Steel Framing | |
| Carpentry | 2 | 27206-13 | Drywall Installation | |
| Carpentry | 2 | 27207-13 | Drywall Finishing | |
| Carpentry | 2 | 27208-13 | Doors and Door Hardware | |
| Carpentry | 2 | 27209-13 | Suspended Ceilings | |
| Carpentry | 2 | 27210-13 | Window, Door, Floor and Ceiling Trim | |
| Carpentry | 2 | 27211-13 | Cabinet Installation | |
| Carpentry | 3 | 27303-14 | Properties of Concrete | |
| Carpentry | 3 | 38101-11 | Rigging Equipment | |
| Carpentry | 3 | 38102-11 | Rigging Practices | |
| Carpentry | 3 | 27306-14 | Trenching and Excavating | |
| Carpentry | 3 | 27304-14 | Reinforcing Concrete | x |
| Carpentry | 3 | 27307-14 | Foundations and Slab-on-Grade | |
| Carpentry | 3 | 27308-14 | Vertical Formwork | |
| Carpentry | 3 | 27309-14 | Horizontal Formwork | |
| Carpentry | 3 | 27305-14 | Handling and Placing Concrete | |
| Carpentry | 3 | 27310-14 | Tilt-up Wall Panels | |
| Carpentry | 4 | 27401-14 | Site Layout One - Differential Leveling | |
| Carpentry | 4 | 27402-14 | Site Layout Two - Angular and Distance Measurements | |
| Carpentry | 4 | 27403-14 | Advanced Roof Systems | |
| Carpentry | 4 | 27404-14 | Advanced Wall Systems | |
| Carpentry | 4 | 27405-14 | Advanced Stair Systems | |
| Carpentry | 4 | 27406-14 | Introduction to Construction Equipment | |
| Carpentry | 4 | 27407-14 | Introduction to Oxyfuel Cutting and Arc Welding | |
| Carpentry | 4 | 27409-14 | Site Preparation | |
| Carpentry | 4 | 46101-11 | Fundamentals of Crew Leadership |
Masonry
This three-level curriculum encompasses modules such as Mortar, Metalwork in Masonry and Estimating
| Craft | Level | Module | Title | Credit |
|---|---|---|---|---|
| Masonry | 1 | 28101-13 | Introduction to Masonry | |
| Masonry | 1 | 28106-13 | Masonry Safety | |
| Masonry | 1 | 28102-13 | Masonry Tools & Equipment | |
| Masonry | 1 | 28103-13 | Measurements, Drawings, and Specifications | |
| Masonry | 1 | 28104-13 | Mortar | |
| Masonry | 1 | 28105-13 | Masonry Units and Installation Techniques | |
| Masonry | 2 | 28201-14 | Residential Plans and Drawing Interpretation | |
| Masonry | 2 | 28202-14 | Residential Masonry | |
| Masonry | 2 | 28203-14 | Reinforced Masonry | |
| Masonry | 2 | 28204-14 | Masonry Openings and Metalwork | |
| Masonry | 2 | 28205-14 | Advanced Laying Techniques | |
| Masonry | 2 | 28206-14 | Effect of Climate on Masonry | |
| Masonry | 2 | 28207-14 | Construction Inspection and Quality Control | |
| Masonry | 3 | 28301-14 | Elevated Masonry | |
| Masonry | 3 | 28302-14 | Specialized Materials and Techniques | |
| Masonry | 3 | 28303-14 | Repair and Restoration | |
| Masonry | 3 | 28304-14 | Commercial Drawings | x |
| Masonry | 3 | 28305-14 | Estimating | |
| Masonry | 3 | 28306-14 | Site Layout - Distance Measurement and Leveling | |
| Masonry | 3 | 28308-14 | Stone Masonry | |
| Masonry | 3 | 46101-11 | Fundamentals of Crew Leadership |
Painting
This three-level curriculum covers topics such as Basic Surface Preparation, Wood Finishing, and Texturing.
| Craft | Level | Module | Title | Credit |
|---|---|---|---|---|
| Painting | 1 | 07101 | Careers in the Painting Trade | |
| Painting | 1 | 07102 | Safety | |
| Painting | 1 | 07103 | Ladders, Scaffolds, Lifts and Fall Protection | |
| Painting | 1 | 07104 | Identifying Surface/ Substrate Materials and Conditions | |
| Painting | 1 | 07105 | Protecting Adjacent Surfaces | |
| Painting | 1 | 07106 | Basic Surface Preparation | |
| Painting | 1 | 07107 | Sealants and Repair/ Fillers | |
| Painting | 1 | 07108 | Introduction to Paints | |
| Painting | 1 | 07109 | Brushing and Rolling Paints and Coatings | |
| Painting | 2 | 07201 | Painting Failures and Remedies | |
| Painting | 2 | 07202 | Job Planning and Completion | |
| Painting | 2 | 07203 | Chemical Cleaning and Stripping | x |
| Painting | 2 | 07204 | Low-Pressure Water Cleaning | |
| Painting | 2 | 07205 | Abrasive Blasting | |
| Painting | 2 | 07206 | Drywall Finishing and Patching | |
| Painting | 2 | 07207 | Stains | |
| Painting | 2 | 07208 | Clear Finishes | |
| Painting | 2 | 07209 | Wood Finishing | |
| Painting | 2 | 07210 | Coatings Two | |
| Painting | 2 | 07211 | Spray Painting | |
| Painting | 3 | 07301 | Painting Failures and Remedies Two | |
| Painting | 3 | 07302 | Job Supervision, Planning and Control | |
| Painting | 3 | 07303 | Coatings Three | |
| Painting | 3 | 07304 | Coating and Tinting | |
| Painting | 3 | 07305 | Decorative (Faux) Finishes | |
| Painting | 3 | 07306 | Wallcovering | |
| Painting | 3 | 07307 | Graphics | |
| Painting | 3 | 07308 | Texturing | |
| Painting | 3 | 07309 | Spraying and Special Devices |
Project Management
This one-level curriculum covers topics such as Construction Documents, Resource Control and Continuous Improvement.
| Craft | Level | Module | Title | Credit |
|---|---|---|---|---|
| Project Management | 1 | 44101-08 | Introduction to Project Management | x |
| Project Management | 1 | 44102-08 | Safety | x |
| Project Management | 1 | 44103-08 | Interpersonal Skills | x |
| Project Management | 1 | 44104-08 | Issues and Resolutions | x |
| Project Management | 1 | 44105-08 | Construction Documents | x |
| Project Management | 1 | 44106-08 | Construction Planning | x |
| Project Management | 1 | 44107-08 | Estimating and Cost Control | x |
| Project Management | 1 | 44108-08 | Scheduling | x |
| Project Management | 1 | 44109-08 | Resource Control | x |
| Project Management | 1 | 44110-08 | Quality Control and Assurance | x |
| Project Management | 1 | 44111-08 | Continuous Improvement | x |
Project Supervision
As a one-level curriculum covers topics such as Human Relations and Problem Solving, Safety, and Quality Control.
| Craft | Level | Module | Title | Credit |
|---|---|---|---|---|
| Project Supervision | 1 | MT201-01 | Orientation to the Job | x |
| Project Supervision | 1 | MT202-01 | Human Relations and Problem Solving | x |
| Project Supervision | 1 | MT203-01 | Safety | x |
| Project Supervision | 1 | MT204-01 | Quality Control | x |
| Project Supervision | 1 | MT205-01 | Contract and Construction Documents | x |
| Project Supervision | 1 | MT206-01 | Document Control and Estimating | x |
| Project Supervision | 1 | MT207-01 | Planning and Scheduling | x |
| Project Supervision | 1 | MT208-01 | Resource Control and Cost Awareness | x |